 |
SLM/QAM/Spectrum Analyzer/DOCSIS3.1 tester - CX350s D3 |
The VePAL CX350s-D3.1 is a portable, all-in-one test solution for legacy analog and digital Cable TV networks, supporting SLM, DOCSIS 3.0/3.1, Ethernet, and T1 test capabilities.
DATASHEET |
 |
SLM/QAM/USG/Spectrum Analyzer/MPEG/DOCSIS3.0 tester - CX380s |
The CX380s-D3.1 is a super-tech installation and maintenance tool for next generation CATV networks. Equipped with a large 7" touch-screen color LCD and intuitive graphical user interface, the CX380s-D3 can be used under all light conditions. This highly flexible unit combines a 1GHz spectrum analyzer with 60dB dynamic range, a forward and return... |
 |
SLM/QAM/USG/Spectrum Analyzer/MPEG/DOCSIS3.1 tester - CX380s D3.1 |
The VePAL CX380s-D3.1 is a next generation test solution designed for analog and digital cable TV networks with enhanced spectrum anaylsis, digital channel, DOCSIS 3.0/3.1, Sweep, MPEG analysis and Ethernet test capabilities. |
 |
Sweep/Spectrum/DOCSIS 3.0 tester - CM300/CM3800 |
The CM3000 and CM3800 analyze Upstream and Downstream network performance for business and bundled services. Both instruments validate the effectiveness of DOCSIS 3.0 services.
DATASHEET |
 |
SLM/DOCSIS tester - CX110+ |
A next generation CATV installer meter to characterize and measure Analog and Digital video signals. For Analog carriers, Peak Video level, single or dual channel Audio levels and Carrier to Noise (C/N) measurements are possible on NTSC, PAL, or SECAM video formats. Digital QAM16/64/256 carriers with or without deep Interleaving are measured... |
 |
SLM/USG tester - CX120+ |
Equipped with the same base feature set as the CX100+, the CX120+ boasts the industry’s first Upstream Signal Generator with FEC capabilities as an option. This unique feature is used to characterize the HFC return path for CW, QPSK, QAM16, QAM64, or QAM128 transmission while QAM analysis is made possible when the unit is used in conjunction with... |
 |
SLM/DOCSIS3.0 tester - CX150+ |
With an embedded DOCSIS 3.0 cable modem, the CX150-D3+ supports full upstream and downstream 8x4 channel bonding, IPv6 addressing and Advanced Encryption Standard (AES) encryption used in next generation DOCSIS 3.0 networks. Cable modem emulation offered by both units provides valuable statistics pertaining to the upstream and downstream paths and... |
 |
SLM/QAM/DOCSIS3.0/USG tester - CX180+ |
An all-in-one, super-tech installation and maintenance tool for next generation CATV networks. The CX180-D3+ can be used at the headend for return path ingress scan and return path QAM analysis. Enhanced ingress monitoring in both the forward and reverse paths is possible across a 50dB dynamic range. Adjustable resolution bandwidths, measurement... |
 |
Datacom/DDS test Module - MTT-9 |
Part of the VeEX Modular Test Toolkit (MTT) family of products, the MTT-9 test module can be used for all your serial Datacom testing requirements, including DTE/DCE emulation for end-to-end testing of data networks, bidirectional monitoring for a greater level of troubleshooting for data networks, FOX testing for Frame Relay CIR verification, and... |
 |
Dual ports Ethernet test Module - MTT50 |
Part of the MTT family of products, the MTT-50 is a powerful service installation and maintenance tool for 10/100/1000 Base-T, 100Base-FX, and 1000Base-SX. With wirespeed traffic generation, this module provides physical layer to IP layer testing. Now with VoIP, packet delay variation, and 100FX support, the MTT-50 significantly reduces repair... |
 |
Single E1/Dual E1 test Module - MTT 27 |
Part of the MTT family of products, the MTT-27 is designed to assist field technicians with new link installation, routine maintenance, and troubleshooting problems in the E1 network. This module comes in two versions, Dual E1 and Single E1, to fit your testing requirements and offers both out-of-service and in-service testing. Also supported in... |
 |
C37.94 test Module - MTT45 |
IEEE Standard C37.94™-2002 defines an Nx64 kbit/s multimode optical fiber interface between teleprotection and digital multiplexer equipment, up to 2 km. The IEEE C37.94 test module for the SunSet MTT is designed to assist technicians in turning up a new network or in isolating problems on both sides (teleprotection and multiplexer) of the network. |
